Special pliers for disconnecting spark plug wires. Ideal for removing spark plug harnesses
Xenon stroboscopic lamp for setting the ignition advance point of old gasoline or LPG engine systems
Assortment kit of heat-shrink tubing in different colors 5 quantity 100 sleeves) see table below Ideal for insulating welds during electrical assembly of LPG or other harnesses
10 White shrinkable heat-fusible sleeve in a heat-shrinkable tube, for 0.3 to 0.8 mm² conductor, diameter from 0.62 to 1.01 mm, length: 25 mm Ideal for insulating welds during electrical assembly of LPG or other harnesses
10 Red shrinkable heat-fusible sleeve in a heat-shrinkable tube, for 0.8 to 2 mm² conductor, diameter from 1.01 to 1.6 mm, length: 40 mm Ideal for insulating welds during electrical assembly of LPG or other harnesses
10 Red shrinkable blue heat-fusible sleeve in a heat-shrinkable tube, for 2 to 4 mm² conductor, diameter from 1.6 to 2.26 mm, length: 40 mm Ideal for insulating welds during electrical assembly of LPG or other harnesses
10 Shrinkable yellow heat-fusible sleeve in a heat-shrinkable tube, for 4 to 6 mm² conductor, diameter from 2.26 to 2.76 mm, length: 40 mm Ideal for insulating welds during electrical assembly of LPG or other harnesses
Tester to check the ignitions on old petrol or LPG vehicles. Allows to control the presence of the ignition coming from the coil without risk...
Short circuit detector / tester / tracer 6v / 12v / 42v all vehicle. Use: Tracing of wires, Verification of short-circuit, open circuit location, wire identification
Battery and alternator load tester Applies high current loads to check battery status. For 6 V or 12 V automatic lead-acid batteries. Also used to test the performance of charging systems. For home or workshop. Length of the 2 cables: 300 mm each.
20 Tools for dismantling car radios + GPS
Cable connection tool
Rare !!! Fabric adhesive tape (smooth material) roll of 25Mx19mm, ideal for finishing electrical harnesses when carrying out LPG installations
Pliers intended to tighten and loosen the clip collars of LPG hoses
Cutting pliers useful for cutting water / LPG hoses and for many other jobs
FACOM model Y103B riveting pliers, used to fix rivets 5 mm in aluminum rivets - 4 mm in steel rivets. Return spring holding the clamp in the open position. Supplied with 3 mouthpieces for 3 - 4 - 5 mm. Guaranteed for life by Facom at all distributors
Black plastic clamps, Length 390mm x width 4.8 mm, essential for fixing cables per pack of 100 pieces
Tools for removing staples and clips
Spark plug wrench 14mm long for Renault, Citroen, Bmw, etc.
VAG 1.2 / 1.4 / 2.0 FSi after 2013 Tool OEM10530 used to secure the dismantling of ignition coils for gasoline FSi: 1.2 / 1.4 / 2.0 in volksvagen, Audi, Skoda, Seat cars after 2013. Ignition puller coil VW Specialist has OEM serial number T10530
Black plastic clamps, Length 290mm x width 4.8 mm, essential for fixing cables in packs of 100 pieces (Discount by quantity reserved for professionals) see table below
TORQUE WRENCH 1/2 28-210 NM WITH EXTENSION 3/8″ BIT LIFETIME WARRANTY Torque wrench 1/2″ 28-210 Nm with extension + 3/8″ bit Tightening a screw or nut requires the use of a wrench. Often, it is the operator who assesses the degree of tightness by measuring the effort. In some cases, this force must be measured by a special tool: the torque wrench.
Set of external circlips - 300pcs.
Contour template, profile copier, length 260 mm – ideal for tiles, carpets, linoleum adapt – for carpentry, modeling and body work – max. Depth measurement: 30 mm – max. Measuring width: 260 mm – Total width: 282 mm – with 4 retaining magnets
1/2″ magnetic angle wrench 1/2″ square drive 360° sector Flexible rod with magnet
Allen key set, internal hexagon, 9 pieces Allen key set, internal hexagon, 9 pieces Allen keys, 9 pieces extra long, color coded long term slip resistance
TORX T-WRENCH SET, T10-T40, 6 PIECES
Set of hexagon wrenches 3/32″ -3/8″ -10 pieces sizes in inches
3-18mm twist drill bit sharpener for all 3-18mm diameter twist drill bits before a vertically rotating grinding wheel adjustable grinding angle, including manual Tool for every day use at an optimal price-performance ratio
Torque indicator with 1/2” square
Vernier caliper for inch nuts
Digital Caliper -150mm Precision digital caliper in cassette Features: internal measurement, external measurement, depth measurement, adjustable to 0 position, extra large LCD display Vernier division: 1/100mm Scale: mm and inch / inch Surface: Chrome Measuring range 0-150mm battery included
Pit jack – 500 kgs New 0.5 ton transmission jack. This hydraulic jack is used to remove, install and transport auto parts. Its main use is to raise and lower transmissions and gearboxes Rated load 500kg Min saddle height 1100mm Maximum saddle height 1900mm Dimensions 1120 x 230 x 280mm
Assembly device disassembly of door pins, length 370 mm Hinge pin puller universally applicable for all vehicles for assembly and disassembly of the car door screw 320mm total length, 190mm height, 6mm wide short side and 14mm long groove 6mm long side bore throughout, 8mm bore with 5mm depth
2000W heat gun Rated power: 2000 Watts Temperatures: 400°C, 600°C, 350°C, 550°C, 25°C Air consumption: 550 l / min, 350 l / min Cooling function: no Softgrip handle: no Safety: overheating protection Weight: 0.8kg
Professional video inspection camera with LCD color screen 640×480 camera IP67 rated waterproof color camera with ultra-thin 8mm camera head and 1m flexible cable. Facilitates the inspection of hard-to-reach areas. Color screen
Brushless impact wrench and fast charge-18v -4 Ah “Brushless” Carbon brushless impact driver with 80-minute high current smart charger and 4 Ah Li-ion battery. It benefits from the latest carbon brushless technology offering better results in terms of performance, battery life and device life. Excellent performance
Magnetic workshop tray (for example on the roller cabinet side) ideal for temporary storage of small equipment during rapid interventions. 6 strong magnets with protection, capacity approx. 4kgs, 10 holes in lower position Ø 19 mm Dimensions: 210 x 75 x 70 mm
Magnetic multi-position tool bowl, ideal for storing screws, nuts, washers and other small keys right where you work, it can also be fixed vertically or horizontally, for example on the column of the impact-resistant plastic deck and mechanical stresses. The magnet is embedded in the material, which protects the paint from scratches. Weight: about 430g
In this section you will find all the small tools commonly used in a mechanical workshop automotive , such as Key & spark plugs, wrench for lambda probe, sensor, tracer, case for bearing, alternator, tools for disassembly of the auto radio, sensor short circuit, fuses, tools, connection cable,booster, sleeves heat shrink, lugs, tape, clamp meter...