- Out-of-Stock
Reference: PROBD-G5
Brand: AIR GPL
OBD2- PROBD-G5 SOCKET EXTENDERBanner
KME BINGO-M ECU
The lambda BINGO-M system is used to control and optimize the gas-air mixture taken in by the engine using the signal from the oxygen sensor. The switch allows you to change from gasoline to gas.
When connected to the tank level sensor, it displays the current level with 5 LED diodes.
KME BINGO-M ECU
The lambda BINGO-M system is used to control and optimize the gas-air mixture taken in by the engine using the signal from the oxygen sensor. The switch allows you to change from gasoline to gas.
When connected to the tank level sensor, it displays the current level with 5 LED diodes.
In the complete kit you will find: the electronic control unit, the main harness, the emulator harness (with or without European connectors), the stepper motor, the switch, the temperature sensor and the small elements disassembly.
BINGO-M Basic Settings
Self-adaption - the device starts working from the initial position and adapts to current conditions.
Oxygen sensor type:
0..1V increase signal,
Signal increasing from 0 to 5 V,
5..0V drop signal,
0.8..1.6V rising signal.
Works with PULL-UP I PULL-DOWN sensors (Bingo-S version).
Throttle Position Sensor (TPS):
Linear signal 0..5V,
> 5..0V linear signal,
no GST,
0-12V switch type (plus connection),
Switch type 12-0V (ground connection),
BOSCH (two ways).
Oxygen sensor emulation:
earth (ground connection),
wave (simulation with the modifiable square wave - frequency, duty cycle),
disconnected (no signal).
Type of driving:
normal,
economic,
athletic.
Tank level sensor type:
9 levels,
0-90ohm,
Reserve.
Engine speed:
choice of the type of ignition system,
choice of switching level (1500-3500 rpm),
switching with increase or decrease in speed.
Additional functions:
CUT-OFF function,
maximum engine speed limit,
adjustment of the minimum temperature for switching to gas (10..60°C).
Advanced settings :
maximum opening of the stepper motor - setting the value in the range 20-255 steps with an accuracy of 1 step,
minimum opening of the stepper motor - setting the value in the range from 20 to 255 steps with an accuracy of one step,
HI state emulation time - range 0.025 to 6.375 seconds, precision 0.025 seconds,
LOW state emulation time - range 0.025 to 6.375 seconds, precision 0.025 seconds,
lambda read delay (open loop delay) - range 0.05-21.15, precision 0.05 (minutes:seconds),
gas/petrol phase overlap time - injector operation time (from opening the gas valve to delivering gas to the mixer) - range 0.1 to 10.0 seconds, accuracy 0 .1 second.
Translated with www.DeepL.com/Translator (free version)
Reference: PROBD-G5
Brand: AIR GPL
OBD2- PROBD-G5 SOCKET EXTENDERReference: 6905640001
Brand: KME.SP Zo.o.
KIT NEVO-SKY JET EXPERT 4 CYLINDERS DG7 RGBReference: 6905581001
Brand: KME.SP Zo.o.
KIT NEVO-SKY JET EXPERT 8 CYLINDERS RL DG7 RGBReference: 6905340001
Brand: KME.SP Zo.o.
KIT 4 CYL NEVO-SKY JET ECO DG7 RGBReference: PROBD2-G5
Brand: AIR GPL
DOUBLE SOCKET EXTENDER OBD2- PROBD2-G5Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent